Electric Trunk Lift Tailgate Control Kit Retrofit for 2022-2025 Peugeot e-308 P5 Hatchback
Trading Properties
Basic Properties
Mr. Wong
- +86 190 6808 0629 Contact Us
| System Voltage: | 12V DC | Rated Thrust: | 370 N Per Actuator |
| Tailgate Mass: | Up To 42 Kg | Cycle Time: | 6-7 Seconds Each Direction |
| Noise Level: | Under 52 DB At One Metre | Sleep Current: | 1.8 MA After 20 Seconds |
| Operating Range: | -30 C To +80 C | Sealing Rating: | IP55 Module, IP67 Actuators And Connectors |
| Net Weight: | 6.1 Kg Per Set | Actuator Type: | Brushless Motor Units With Helical Gear Train |
| High Light: | Electric Trunk Lift EV Ready,Automatic Trunk Opener Quiet Drive,Auto Tailgate Retrofit P5 |
||
Electric Tailgate Retrofit for the Peugeot e-308 P5
Battery-electric cars change the rules for tailgate conversions. There is no engine noise to mask a whining actuator, no exhaust heat to dry the underside of the bumper, and the 12V auxiliary battery is managed by the vehicle's DC-DC converter rather than a constantly charging alternator. This kit for the e-308 P5 was specified with those conditions in mind: brushless-drive actuators chosen for low acoustic signature, a control module with a true sleep state to protect the auxiliary battery, and sealed connectors rated for the damp, salt-laden airflow around an EV rear bumper.
Specification Highlights
- Electric trunk lift tuned for quiet running — the actuator gear train uses helical cut gears and a rubber-isolated mount, so the door moves at a noise level that stays discreet in a vehicle with no engine sound.
- Automatic trunk opener with EV battery care — after the last command the module enters a 1.8 mA sleep state, and it wakes only on a valid trigger, so the auxiliary battery is not drained between journeys.
- Auto tailgate retrofit for the P5 body — bracket geometry and stroke length are matched to the e-308 hatchback, including the slightly different inner panel used on the electric version.
- Soft close pull-in — the latch is drawn in electrically, which matters on an EV where a mis-closed boot is often heard before it is seen.
- Corrosion-resistant hardware — stainless fasteners and a zinc-nickel finish on the brackets cope with the salt spray that collects around a rear bumper with no exhaust airflow.
- No vehicle coding — the module works alongside the factory smart key and body computer without a diagnostic session, so the vehicle's warranty-sensitive software is untouched.
Technical Data
| Parameter | Specification |
|---|---|
| Fitment | Peugeot e-308 P5, 2022-2025 |
| System Voltage | 12V DC auxiliary system |
| Actuators | Brushless motor units, helical gear train |
| Rated Thrust | 370 N per actuator |
| Tailgate Mass Supported | Up to 42 kg |
| Noise Level | Under 52 dB at one metre |
| Cycle Time | 6-7 seconds each direction |
| Triggers | Smart key, cabin switch, handle switch |
| Sleep Current | 1.8 mA after 20 seconds |
| Safety | Bidirectional obstruction reversal, over-current cut-off |
| Sealing | IP55 module, IP67 actuators and connectors |
| Operating Range | -30 C to +80 C |
| Net Weight | 6.1 kg per set |
Fitting Notes for EV Workshops
Isolate the auxiliary battery before working, as with any 12V retrofit on a high-voltage vehicle. The trim removal sequence follows the same clipped panel design as the combustion-engined 308 hatchback. Brackets mount on the original ball studs; the harness follows the factory path and terminates at the auxiliary battery junction box with the supplied fused lead. Allow 2 hours for a first fit; the job does not touch high-voltage components, so no HV qualification is required beyond normal workshop safety procedure.
Who This SKU Suits
EV-focused accessory retailers, Peugeot dealers adding aftermarket options to new e-308 deliveries, corporate and leasing fleets electrifying their pool cars, and converters who already supply charging accessories and want a complementary comfort product. The e-308 is sold across France, Germany, the Netherlands, Belgium, Spain, Italy and the UK, and demand skews toward company-car drivers who value hands-free loading and quiet operation.
Packing and Warranty
Kits ship in a printed carton with antistatic bags for the module, foam-cradled actuators and a five-ply export outer box. Every set is cycle-tested 300 times, with checks on acoustic signature, sleep current, obstruction reversal and connector water resistance. Production is ISO 9001:2015 certified. Warranty is 24 months on actuators and 12 months on the control module; individual parts can be reordered as service items.