Power Lift Gate Trunk Auto Tailgate Control Device Kits Modification Retrofit for Peugeot 308 SW T9
Trading Properties
Basic Properties
Mr. Wong
- +86 190 6808 0629 Contact Us
| System Voltage: | 12V DC | Rated Thrust: | 400 N Per Actuator |
| Tailgate Mass: | Up To 48 Kg | Stroke Time: | 8-9 Seconds Each Direction |
| Operating Range: | -30 C To +75 C | Housing Protection: | IP55 Module, IP65 Actuators |
| Net Weight: | 7.4 Kg Per Set | Construction: | Anodised Aluminium Tube, Zinc-plated Steel Rod, PA66 Ends |
| Actuators: | Twin Motorised Lift Actuators, Synchronous Drive | Height Memory: | Adjustable, Non-volatile |
| High Light: | Electric Trunk Lift Control Device,Automatic Trunk Opener Modification,Auto Tailgate Control Kit |
||
Peugeot 308 SW T9 Power Liftgate Retrofit
The 308 SW estate (T9, 2013-2021) has one of the longest tailgates in the segment, and on a cold morning the manual struts barely hold it open. This retrofit replaces that weak point with a motorised control device: two electric actuators, a control module, a plug-in loom and estate-specific brackets, all matched to the wagon body rather than the hatchback. The module ships pre-configured, so the fitter connects power, plugs in the actuators and the boot opens from the key, the cabin switch or the handle — no laptop and no dealer session.
What Makes This Kit Different
- Electric trunk lift with a dedicated control device — the module manages both actuators in sync, which keeps the wide estate tailgate level through the stroke instead of twisting on one side.
- Automatic trunk opener with soft close — the last few centimetres are pulled in electrically, so the door shuts with a light touch and the seal seats evenly across the full width.
- Auto tailgate for estate body geometry — bracket lengths and actuator stroke are set for the SW roofline, so the door clears tall loads and reaches full height without contacting the roof rails.
- Three-way trigger — key fob, dashboard button and original handle switch all work, and the factory remote is left untouched.
- Obstruction reversal — both directions are monitored, so a low beam or an outstretched arm stops the door instead of forcing it.
- Programmable height — owners can cap the opening angle for low car parks and the setting survives a battery change.
Technical Specifications
| Parameter | Specification |
|---|---|
| Fitment | Peugeot 308 SW T9 estate, 2013-2021 |
| System Voltage | 12V DC |
| Actuators | Twin motorised lift actuators, synchronous drive |
| Rated Thrust | 400 N per actuator |
| Tailgate Mass Supported | Up to 48 kg |
| Stroke Time | 8-9 seconds each direction |
| Triggers | Key fob, cabin switch, handle switch |
| Safety | Bidirectional obstruction reversal, over-current cut-off, P-gear interlock |
| Height Memory | Adjustable, non-volatile |
| Housing Protection | IP55 module, IP65 actuators |
| Operating Range | -30 C to +75 C |
| Construction | Anodised aluminium tube, zinc-plated steel rod, PA66 ends |
| Net Weight | 7.4 kg per set |
Fitting Guide Summary
The SW trim panel is held by clips along the glass edge and two screws behind the grab handle; a trim lever and a T20 driver cover the whole removal. The actuator brackets reuse the factory ball studs, so no drilling is required, and the loom follows the original routing through the roof-side grommet. Expect about 2 hours for a first fit and 60-70 minutes for a repeat. The install is fully reversible: original struts can be refitted when the car changes hands, which is useful for leasing and part-exchange vehicles.
Typical Buyers
Peugeot specialists and general aftermarket wholesalers in France, Belgium, Portugal, Poland and Turkey; taxi and private-hire operators running 308 SW estates; dog-owner and outdoor accessory retailers, since the SW is a popular estate for pet transport; and mobile fitters who work at customer sites. Estate owners are a loyal, high-retention group because the body style stays in production for eight years and the platform is shared with several sibling models.
Carton, Testing and Service
Kits are packed in a printed carton with die-cut foam blocks, then in five-ply export cartons with corner protection. Bench verification covers 400 duty cycles, synchronous travel alignment, obstruction reversal force and standby current. Neutral packaging is available for private-label sellers. Manufacturing is ISO 9001:2015 certified, with 24-month cover on actuators and 12 months on the control module; individual actuators, modules and harnesses can be reordered as service parts.