2025 Electric Tail Gate Lift Trunk Opener Power Back Door Kit for Peugeot 3008 P64 Automatic Boot Opening System
Trading Properties
Basic Properties
Mr. Wong
- +86 190 6808 0629 Contact Us
| Supply Voltage: | 12V DC | Stroke Time: | 6-7 Seconds |
| Breakaway Torque: | 45 Kg Class | Housing Rating: | IP56 |
| Working Temperature: | -35 C To +80 C | Idle Consumption: | 2.5 MA |
| Kit Weight: | 7.2 Kg | Actuation: | Two Electric Lift Actuators |
| Sensor Type: | Capacitive Kick Sensor | Bench Test: | 500 Cycles |
| High Light: | Electric Tailgate Kit Soft Close,Automatic Trunk Opener Kick Activated,Car Electric Trunk Back Door |
||
2025 Electric Tail Gate Lift Kit for Peugeot 3008 P64
A 2025-specification power back door kit engineered for the second-generation Peugeot 3008 (P64). The set contains two motorised lift actuators, a CAN-aware control unit, a complete plug-in harness and model-specific brackets, and it mounts onto the factory strut studs so the original hatch geometry is preserved. Because the P64 tailgate is aluminium-faced and heavier than earlier Peugeot hatches, the actuators are tuned with a higher breakaway torque so the door starts moving smoothly from the fully closed position instead of stalling on the latch.
Core Selling Points
- Electric tailgate kit with soft close — the final centimetres of travel are handled by an electric latch pull, so the tailgate never needs to be slammed and the seal compression stays uniform over the vehicle's life.
- Automatic trunk opener, kick activated — the optional foot sensor sits behind the rear bumper cover and reads a short kick gesture; detection is filtered so a passing pet or a puddle splash will not trigger the door.
- Car electric trunk and power back door in one unit — key fob, cabin switch, hatch handle and the foot sensor all route through the same control unit, so there is one firmware and one part number to stock.
- Height memory — the driver can teach a lower opening point for low-ceiling car parks, and the setting survives a battery disconnect.
- Dual-stage obstruction logic — a hall sensor tracks position while the control unit watches motor current, so both obstacles and end-stop overloads are handled.
- Sleep mode — after 30 seconds idle the module drops to a low-draw state to protect the battery on vehicles that sit for long periods.
Technical Data
| Parameter | Value |
|---|---|
| Suitable Model | Peugeot 3008 P64, 2016-2023 |
| Supply Voltage | 12V DC |
| Actuation | Two electric lift actuators, ball-socket ends |
| Breakaway Torque | Designed for aluminium tailgate, 45 kg class |
| Stroke Time | 6-7 seconds |
| Inputs | Key remote, cabin switch, hatch switch, foot sensor (optional) |
| Safety | Hall position sensing plus current-based reversal |
| Sensor Type | Capacitive kick sensor with rain and splash filter |
| Housing Rating | IP56 |
| Working Temperature | -35 C to +80 C |
| Idle Consumption | 2.5 mA in sleep state |
| Kit Weight | 7.2 kg |
Fitting Overview
Installation is a plug-in retrofit: remove the rear trim, swap the gas struts for the motorised actuators, route the supplied harness along the factory loom path, and terminate the fused power lead at the battery junction box. No body cutting is involved and the original struts can be refitted when the vehicle is returned to stock condition. Typical labour is 2 hours for a technician unfamiliar with the model and under an hour for a repeat fit; a printed guide plus a QR-linked video cover the P64 trim clips and the sensor calibration steps.
Where This Kit Sells
Accessory distributors with strong Peugeot coverage in France, Belgium, Turkey and North Africa; online shops targeting SUV owners upgrading boot convenience; leasing companies and corporate fleets running 3008 crossovers that need faster loading cycles; and installers doing mobile fitment at customer sites. Since the P64 shares its platform with several Stellantis models, the same fitting skill set transfers across a broader accessory range.
Packing and Service
Each set is packed in a printed box with EVA foam inserts, then in a five-ply export carton with corner reinforcement. Every unit is cycle-tested 500 times on the bench before packing, with checks on stroke time, sleep current, sensor response and reversal force. The line is ISO 9001:2015 certified; warranty is 24 months, and actuators, sensors and control units are available as individual service parts for after-sales support.